Do you want to maintain your bike's good looks and performance? Cleaning your motorcycle on a regular basis will keep it looking sharp (and make you look better too), and it can also help keep your bike running smoothly. The following are recommended steps for cleaning your motorcycle.

Pre-Wash Steps

First, water doesn't mix well with every part of your bike, so make sure that the necessary parts of your bike are protected from water. In order to prevent water from entering the exhaust pipe, or pipes, plug the ends. Most dealers or parts stores carry universal exhaust plugs, but if you are without them, you can carefully place a plastic bag around the opening and either tie it in place, or use a strong rubber band.

Also, the air filter will need to be protected. The best way is to simply remove it, or you can use a plastic bag to keep water away.

If you find the engine cases are really greasy, use a small brush, like an old toothbrush, and apply engine degreaser. Steer clear of the chain, sprockets and wheel axels, as the degreaser can potentially cause some nasty problems.

Finally, ensure that the spark plugs, battery caps, gas cap, oil filler cap, and the engine oil lever cap are all secured so no water can get into the engine.

Washing Your Bike

You can rinse off the dirt and the degreaser using a garden hose--be careful that you're not using too much water pressure. You want to use just enough to clear your bike of dirt and degreaser. Using too much pressure could get water into the front forks, or transmission seals. Wheel bearings can be susceptible to water creeping in also.

When most of the gunk is rinsed off, go over your bike with warm water and mild soap. Don't forget that toothbrush, or some other type of small brush for areas that are tough to reach.

After washing the bike, it's not time to take a break yet--you should immediately rinse it off with clean water, and then dry it as best you can. Pay particular attention to the chain--you don't want rust to develop, so make sure it's good and dry, and then lubricate it with chain lube. For your chrome parts, you can make those shine with auto chrome polish.

If you would like to wax the painted and chrome parts of your bike, make sure you use an automotive wax. You don't want to apply wax that contains abrasive material that could scratch or damage parts.

When you are finished, don't forget to remove any plastic bags you used to cover the exhaust pipes or air filter, and start the engine. Let it run for a few minutes to let all the water dry, and to ensure there is no water damage.

Now take that beautiful bike out on the road . . .

Author: Jim Buchanan

About the author:
Jim Buchanan is a writer for Honda Parts House. For more information and for all your motorcycle parts needs please visit http://www.hondapartshouse.com.

Article source: Free Motorcycles Articles.

Of course you already know that it's even more important than usual to drive safely when the weather is cold. In bad weather conditions, it's necessary to pay attention to wet and icy roads, to make the riding experience as safe as possible.

Don't forget to keep warm. Liners under helmets can help keep heat in, and of course don't forget to dress properly--hopefully you have some cold weather riding gear. It's much easier to drive, and keep your concentration sharp when your body is warm. Getting too cold can cause our body reactions to slow down, and if you start thinking about how cold you are, you might not notice the patch of ice that's coming up. Especially keep your hands warm--a good pair of gloves are vital to ensuring an enjoyable ride in cold weather.

It's always best to completely avoid slippery spots in the road. If those spots can't be avoided, make sure you are driving at a reasonable speed to be able to deal with any wet and/or slippery areas. Be sure to reduce your speed enough when you are going around corners--it can be harder to stop if the roads are in less than perfect shape.

When you need to brake on slippery surfaces--it is usually best to use both brakes. Applying the brakes slowly and gradually can help keep the front wheel from locking up. Also, if you are moving at a very low speed, you can try using your feet to help by letting them slide on the road--this can also help prevent a fall.

Be especially vigilant for obstacles, debris, and oil spots in the road--anticipate any potential problems, and manage your speed appropriately.

By being smart, and keeping warm, you can effectively and comfortably ride in cold weather, which can extend your riding season.

Author: Jim Buchanan

About the author:
Jim Buchanan is a writer for Honda Parts House. For more information please visit http://www.hondapartshouse.com

Article source: Free Motorcycles Articles.

If you are anything like me, and for your sake, I hope you are not--when you want something, you don't always take the time to think things through and get the best possible product. For some reason this seems especially true when dealing with items that are very costly, which makes that instant gratification habit doubly worse. Today I want to discuss some steps to take when purchasing a motorcycle.

Sure, it would be cool to buy the biggest baddest bike on the block, but you will be much better off if you can display a little patience, which in the long run could save you some trouble and lots of money.

Research

First, you need to decide which bike is the best for you. Figure out what you are going to use your motorcycle for--cruising on the road, taking on trails, going super fast, etc. Talk to someone knowledgeable and do some research online. Really try to narrow down your choices of the type of bike you want. One of the most important starting points is--what can you afford to pay? It's vital to remember that insuring a motorcycle can be costly, particularly if you are young.

More Research

Getting the idea? Knowledge is power, and in this case, it's the power to make a better decision. There is nothing worse than running out to get a motorcycle only to find that it's too much for you to handle, has too much upkeep, you can't afford it, etc. Look at the market. What benefits are offered by each brand, and more importantly, which benefits work for you the best. Find out all you can about the models you are interested in, visit online forums, read reviews, and by all means don't be afraid to ask the dealer questions. Make sure you get what you want--if the bike you want isn't available, go somewhere else to find it, or wait until it becomes available. Take it for a test ride, see how you feel while riding, is it easy for you to handle? Does it fit you?

Go with Your Gut

Finally, after going through the data gathering stages, narrowing down your choices, and taking the bike for a test ride, if you feel a little odd about the bike, if something doesn't feel quite right, allow yourself some time to think about it before you make the commitment to buy. Another bike will always come around, so you should never feel like you are being forced into anything.

The bottom line is make sure you get something that you want, and are happy with . . . it will make the riding experience that much better.

Author: Jim Buchanan

About the author:
This article was written by Jim Buchanan. For your Honda motorcycle parts and accessories needs, visit http://www.powershondaparts.com.

Article source: Free Motorcycles Articles.

Purchasing a Motorcycle Helmet

When looking to purchase a new motorcycle helmet, there is a lot more to think about than what cool colors and designs are available--the helmet needs to fit properly and be made of material that satisfies your safety needs. It's important to remember that not all helmets are made the same--some helmets are safer than others.

There are a ton of helmet makers out there, so you will have to sort through some information. Online research is a good place to start, also you can ask a local dealer or an experienced rider for their input.

One extremely important safety factor that often gets overlooked when shopping for a helmet is the visibility of the helmet. You need to make sure that the helmet doesn't impair your peripheral vision. A motorcyclist needs to be able to scan constantly, and you don't want any blind spots caused by your helmet. Quick reaction time is vital to avoiding accidents, and a helmet that limits visibility is an open invitation for trouble.

Another factor is the performance of the helmet--is it made of sturdy enough material to protect you in an accident?

When searching for a helmet, you should consider a brighter color, which can be seen easier by other drivers, even at night. Car and truck drivers sometimes have difficulty in seeing bike riders, and a brightly colored helmet can make the rider's presence stand out.

The shape of the helmet must also be considered. You need to ensure that your head fits comfortably into the helmet--don't make any concessions on this point just because of the looks of a helmet. People's heads are shaped differently, so be certain you get a comfortable fit. If you are struggling to find a good-fitting helmet, sometimes it helps to also obtain a liner. Helmet liners are made for comfort, but can also help a helmet fit better. You need to try them on with the helmets to ensure that you get a proper fit.

While there is certainly nothing wrong with buying a helmet online, it's imperative that you actually try helmets on before buying. You want to be sure that it fits properly. Perhaps you have found a website with great deals on motorcycle helmets--rather than simply firing off an order, visit a local dealer, and try on the helmets that you like, so you know exactly what size and type of helmet fits best. Probably the biggest problem with buying helmets is that buyers frequently put factors like appearances or availability ahead of the fit and safety of the helmet, which could lead to some serious results. As with almost everything in life--safety first!

Author: Jim Buchanan

About the author:
Jim Buchanan is an Internet Marketing Specialist for Mindscape at Hanon-McKendry. His hobbies include reading, writing, going to concerts, sports, and riding motorcycles.

Article source: Free Motorcycles Articles.

As summer draws near, the call of the open road beckons you to seek out new adventures. Here are a few tips to help you plan for your next motorcycle road trip.

Packing for a motorcycle trip takes a little more thought than packing for a trip in the car. You have limited storage space and plenty of items that you might need along the way. The key is to pack as compact and lightweight as possible. If you're not sure you'll need an item, remember that you can always pick up an extra sweatshirt or other item along the way.

Instead of packing bulky clothing for cold weather, pack layers. The warmer it gets, the more layers you can shed, and if the weather turns colder, you can always pile on more layers. Remember to pack your rain gear and a safety and repair kit for emergencies on the road. If you plan to pick up a few souvenirs along the way, leave enough extra storage room for those as well. Don't forget to pack a travel motorcycle cover to protect your bike on the road. A cover not only shields your bike from the elements but it also keeps it out of sight from vandals and thieves. Secure a lock through the grommets for extra protection.

When you fill your saddlebags, try to balance out the weight on each side as much as possible. Pack heavier items in the bottom for a stable base, and leave the lighter items for on top. Engine guard chaps serve a double purpose by keeping your feet warm and dry and providing extra storage space for maps, sunglasses, a water bottle, cell phone, flashlight, or other small items. Engine guard chaps, or soft lower covers, keep your feet from getting soaked in the rain or chilled in cold weather.

Perform a thorough maintenance check on your bike to make sure your trip goes as smoothly as possible. Follow the T-CLOCS method compiled by the Motorcycle Safety Foundation:

Tires and Wheels: Check for proper inflation and make sure you have enough tread left for the miles you plan to cover.

• Controls: Inspect the throttle, cables, hoses, and levers.




• Lights: Check the headlights, tail lights, turn signals, and brake lights.




• Oil: Check fluid levels and top off or change as needed.




• Chassis: Make sure your frame, suspension, belts, and fasteners are working properly.




• Stands: Make sure your center and side stands are able to support the weight of your motorcycle.

As a safety measure, let someone know your travel plans and when you plan to come home from your motorcycle trip. You can still be flexible along the way. Just let that someone know if your plans change. Leave room to be spontaneous. That's where you make the best memories.

Author: Jesse K. Taylor

About the author:
� 2009 DuraShield Covers. Save up to 50% off retail on DuraShield travel motorcycle covers and engine guard chaps at www.durashieldcovers.com. Free shipping on all orders!
Find more motorcycle travel tips at the DuraShield Blog.

Article source: Free Motorcycles Articles.

Do you find difficult to restore or repair your motorcycle?Well,you are not alone with this problem.Most of us are not too handy,specially,if we need to deal with a complicated technical issue.Don`t worry about this,that`s fine.Probably you could do it if you would have a Motorcycle Repair Manual.Without a detailed,step-by-step instruction everyone feels lost.

Perhaps it isn`t easy to do it yourself,but let me make a few examples.Let`s say you want to reshape your saddlebag.There is no need to pay for a mechanic to get the job done.Neither you need to buy extra tools.

Let me start.Soak the bag in hot water for a minute.Then stuff it with newspaper,at least a weekend edition.When still wet,put the top back into shape.Just leave to dry for at least one day.Then take out the newspaper.That`s it.Quite simple.If you wish to have the shape longer,you can put stiffeners in.

Here is an other example how to change your motorcycle`s disc brakes.You may know,if you have disc brakes,you need to change the pads once in a while.When you have the new pads ready to built in,get your bike on a stand,so the wheels hang freely.Then loosen off the caliper assembly intact.After remove the used pads.Put the new ones on.Don`t forget to change the brake fluids.Finally replace the caliper assembly.

Now you can see you don`t have to feel difficult to repair your motorcycle by yourself. Motorcycle Repair Manual is very helpful of course and easier to restore your bike if you have a good description in your hand to follow.

Author: Zoltan Torjeki

About the author:
If you are ready to get your hands oily,jump on your bike and spin along to http://tinyurl.com/MotorcycleRepairManual for more repair instructions.

Article source: Free Motorcycles Articles.

Bikers use many accessories for a secure yet stylish riding, thus giving them security from unfortunate, unseen accidents and injuries. Just imagine it's really cold outside and you are biking on streets with bare hands, you will realize well why no rider should ride outside without their motorcycle pair of gloves.

Biking gloves have much wider usage merits as compared to an ordinary pair of gloves. These act as shelter for rider's hands and in serious case of any accident they take the hit instead of precious hands.

Actually motorcycle gloves protect your hands and fingers, otherwise they may be prone to grow numb making it impossible for you to handle your ride. Vital is to have knowhow, that which type of motorcycle gloves to buy from options available. Otherwise it's very likely you will probably end up buying the wrong pair of gloves.

Motorcycle gloves are available in many styles, colors and materials. So one can choose a glove according to his/her choice and need. Motorcycle Gloves at jackets4bikes are available in Leather, Cordura and Mesh materials. Now it solely depends on one's need and requirement that which gloves should be bought.

Biking Leather gloves totally are season friendly; hence they look awesome while wearing at all times of the year. In summers motorcycle leather gloves keep you cool while in winters they protect you from cold. They are a symbol of fashion yet being practical. This uniqueness is what that departs motorcycle leather gloves from all other dresses.

These can be worn anywhere and can be used for varied purposes. Durability, flexibility, lasting nature, protective, versatile are some of the features that are absolutely doubtless about motorcycle leather pair of gloves.

Mesh or perforated leather gloves are best suited for people who ride in warm weather these gloves offer ventilation to keep hands cool and thus one won't tempted to ride without gloves. These mesh or perforated leather biking gloves are wearable throughout the year as they are have no ventilation issues, because of perforated leather used in them.

Water-resistant/water proof motorcycle gloves are best for those bikers who love to ride in rain.

Manufacturers/Sellers are providing huge varieties of gloves of different shapes, size, and colors depending on the choice of the consumer.

Cordura gloves for all biking are designed to be long lasting and resistant to abrasions, tears and scuffs.

While buying motorcycle gloves one can even look for biking gloves that offer excellent knuckle protection. Gloves should have metal or plastic armor over the knuckle area. A heavy duty palm with Kevlar, metal or thick leather will provide protection to one's hand with comfortable lining yet flexible.

Black is an all time favorite and a preferable color but choosing other vibrant and bold colors; matching motorbikes, pants and jacket is not a bad idea itself.

Number of different brand seller are in market so no matter which pair of gloves one chooses to buy, be sure to be comfortable yet protected with it and that you should enjoy wearing them for many hours.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

In the first article of the series we discussed how to change your oil, in the second we talked about tire evaluation and repair. This article is going to focus on (1) battery evaluation; and (2) maintenance and air filter evaluation/cleaning.

1. The best way to prevent battery power loss during extended periods of non use is to hook your battery up to a trickle charger. If you choose this option, make sure that you follow the manufacturers guide lines and instructions very closely. I have heard of instances where the improper use of trickle chargers has caused fires which resulted in significant property damage.

If you didn't get to ride your machine during the winter and you didn't have it hooked up to a trickle charger, chances are your battery is a little low. Check the fluid level, add water to the manufacturers recommendation, then hook it up to a charger and let it sit for the amount of time recommended by the manufacturer of the charger. If it the battery took the charge and has enough power to start your ATV, then you have succeeded, if not you will need to replace it.

2. When was the last time you changed/cleaned your air filter on your ATV? Look at your owners manuals and see what they recommend. There is a lot of variation in the types of riding we do. If you constantly ride on dusty trails following other riders then you will need to change/clean it on a more frequent basis. Lack of cleaning/changing can cause significant power loss and/or engine damage as dirt particles get sucked into your engine.

There are two main types of air filters:

a. Foam filters consist of a foam stretched over a plastic basket structure. To clean these filters rinse the foam with gasoline and then ring the gasoline out. Repeat this process until all of the oil and dirt has been washed out of the filter. Next rinse it with oil and then ring out most of the excess oil. The oil is used to keep dirt particles from passing through into the engine. Replace the foam around the basket and apply a coating of grease along the portion of the filter that rests against the machine. This coating of grease acts as a seal to keep dirt from getting between the machine and the filter.

b. Paper cartridge type filters. You can extend the life of these filters by removing dirt from them with an air compressor. Grease is also used to seal these filters in place.

Author: Bryan Coats

About the author:
Bryan Coats is an avid ATV rider and one of the two owners of the website http://www.AtvTrailReviews.com, which provides a listing of ATV Trails and several
ATV Blogs.

Article source: Free Motorcycles Articles.

Life is becoming faster day by day; and biking is a growing undeniable passion these days, growing in popularity with every passing split of second. Bikers are ranging from street riders to high town competitors. But whatever preference is given by riders, must are bumps on bruises on their ways.

Exactly that is why riding attire is now days being manufactured, keeping in mind issues of safety and protection first. A good racing jacket must protect you in the most types of unseen accidents or in case of any injury.

Bottom line is that manufacturers have now come up with riding jackets offering protection to body parts more prone/exposed to damage. Generally motorcycle jackets either made for men or women ought to come with some permanent or removable foam or plastic compound or rubber made body armor above or inside the apparel. This actually helps keep the body parts safe under the protection of the armor used in motorcycle jackets.

When looking to purchase a racing jacket and/or suit, make sure the armor is CE marked and approved. This 'CE' Certifique Europe is a European standard of certification that grades armor on three levels, level 1 being the least protective, level 3 highest in protection.

Least protection of riding armor jacket should be in areas of shoulders, elbows and if available also for back then it's icing on the cake. Armor jackets at jackets4bikes are very competitive offering armor protection in all motorcycle materials like leather, mesh and Cordura. Some jackets have five section removable armor for back, shoulders and elbows. Armor is completely removable through Velcro locked pockets. Shoulder and elbow armor is made of injection-molded plastic padded with foam. This provides superior protection as compared to standard foam armor.

While other armor jackets have also five section removable armor for back, shoulders and elbows, but that is an double density armor used for protection. Some jackets also offer CE Marked/Approved five section removable dual density armor for back, shoulders and elbows. Armor is completely removable through Velcro locked pockets.

Racing jackets often come with padding of Kevlar or other stress tolerant material near injury prone parts, especially the limb joints. Jackets are generally made of any leather based material, with stretchy materials near the joints to provide maximum comfort.

Back protectors are not often found in racing jackets. Protection for back is normally not a common practice followed by manufacturers for making biking armor jackets for both; men and women. Usually these armors are made up of hard plastic. Also there in some jackets a pocket/place to insert removable back protector is available, which is itself a blessing in disguise.

Otherwise absolutely being without no back protection makes a motorcyclist prone to direct injuries to the back which may are generally caused by flying particles or spinal injuries are generally as a result of a hit/blow near the two ends of the torso. This situation may turn very unfortunate, if it proves to be a hard injury for which the best way out is to pamper you with biking jackets manufactured with back protector as well.

However the importance of the comfort should not be over looked by the rider while purchasing an armor motorcycle jacket. Key to remember is that if you are not comfortable while what so ever jacket you wear, it surely can adversely affect your ride. So pay no head to fears of injury, just grab a good armor jacket and be the best fearless biker.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

Zooming successfully on the roads, a thrill that peps up the adrenalin� that is exactly what the mini choppers do. Now what are these riding geeks? Mini chopper is a type of pocket dirt bike. It is like a small version of motor cycle appearing like a chopper. They are made of steel pipes or even steel tubes and have 4 stroke cc engine. They can store up to four litres of fuel also. The driving capacity is 75 kmph. The mini choppers are also fitted with mechanical brakes. Mini choppers can be drive on uneven surfaces and rough dirt roads. This makes them a cross country choice also for weekend bikers. Since they are lighter they give a feel of a chopper at a reasonable cost.

Amongst the most favoured types, those who can customise the chopper are happy riders. By understanding the dynamics of his machine, the rider can use it to the optimum level. Customized chopper are light weight with low seat height, to give a feel of chopper. Other types are of electric and variety. Electric mini choppers are much cheaper than gas mini choppers. They are best suited for new bikers and children. However gas mini choppers provide faster speed. This means the rider has to be more careful and skillful. They also come in smaller sizes compared to ordinary mini choppers.

Buyers have been attracted to mini choppers worldwide. They provide great thrill and fun which has increased their demand. They are more frequently used in racing and other sport events. Folks also use these mini choppers to experience a blissful and pleasant ride. These choppers are safer and comfortable too. They are known for their trendy looks and come in different sizes and colors. Young adults prefer their mini chopper with gorgeous looks and maintain them very well. They are funky, small, looking marvel with a touch of class. They usually range from 50 to 200 cc cutting across various age groups. They leave a lasting impression provide satisfaction with a sense of pride to the rider.

Because of its growing market, the bike manufacturers have started adapting brand new styles and designs. They are also trying to bring in innovations to the existing features of mini choppers to satisfy bike fanatics. Undoubtedly these sizzling mini choppers have brought in huge resounding profits to manufacturers and has started ruling the automobile industry worldwide.

Author: Alice Shown

About the author:
Visit Thesportsbikeshop for comprehensive information on Mini choppers .

Article source: Free Motorcycles Articles.

Gloves are a famous accessory amongst all the people throughout the world. They successfully give protection against weather changes and also while working they keep our hands safe from harsh working situation, a worker is prone to face. Gloves are available in many varied materials and shapes according to changing needs of different individuals from diverse working industries.

There are many famous garments to make gloves like leather, Cordura, mesh etc. These garment also known as mitts, are being used in garden work, kitchen work, driving, riding of motorcycles as well as in sports activities like rugby, baseball, skiing among others. Carbon Kevlar gloves are just one from many types of gloves.

While reading through it you may jolt your mind about what actually is Kevlar? Basically Kevlar is a high performance Para aramid synthetic fiber. It was originally developed by DuPont in 1965 by Stephanie Kwolek and Herbert Blades but it was to be commercially used by the early 70's.

This Para-aramid fabric is a very exceptional fiber has an exceptional feature that gives maximum strength to keep our hands safe even in extremely higher temperatures. Highly resistant to cuts, abrasions, friction and heat these gloves offer maximum dexterity of the fingers and provide high comfort.

Kevlar basically can protect your hands if it comes into contact with fire, or if a biker accidentally falls badly on a road. The friction produced between rider's hands and road actually will be absorbed by Kevlar. When any motorcyclist faces a high fall on a sliding road actually it's the hands that are used to try stopping oneself or protecting oneself from worst. This makes biker hands prone to face higher friction, resistance which does produce higher heats as a result of friction produced as well as bruising him all over. Kevlar has a property actually that where temperatures are as high as 350 degrees Celsius, it won't melt into your skin due to friction and high heat.

Gloves made from Kevlar fiber will not burn at any point of time, or even melt at scorching temperatures. These make hands more secure against hot metal splashes and open flame. Meaning there by that they do not melt easily; neither can you burn your hands easily.

An Ideal pair of gloves for motorcyclists; as they protect the hands from cuts, bruises and abrasions. Made from very thick material that is not easily penetrated, and which on the other hand offers support to the wrists and fingers. While in some gloves tear and abrasion resistant Para-aramid fabric is for protection on knuckles and fingers.

Actually gloves manufactured for safety during riding typically incorporate precurved fingers section and the best available protection, obtained through additional armor incorporated within the glove. Additional protection actually involves carbon panels for knuckles and the joints of the fingers.

Adding more to it biking gloves may and often do incorporate additional wrist and other protection panels to protect the heel of the hand, back of the hand and other easily injured parts of the hand.

People die heart fans of riding and motorcycle racing definitely need to have their hands well protected against abrasive surfaces, splinters from wood and metal and from other injuries. Bikers need gloves which basically provide support for the different parts of the hands like wrist, fingers and also should be able to give a cushioning effect to the hands, to enhance comfort feeling.

Then why not go out and search Carbon Kevlar Gloves! Go and grab your pair of gloves, you would never repent spending dollars on them.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

A 12-volt motorcycle battery is made up of a plastic case containing six cells. Each cell is made up of a set of positive and negative plates immersed in a dilute sulfuric acid solution known as electrolyte, and each cell has a voltage of around 2.1 volts when fully charged. It comes in many shapes, size and power depending to the model of your motorcycle.

You may already know that there are 2 main categories that motorcycle batteries can fall into - maintenance free and conventional. For conventional type, it requires you to constantly adding water because of normal process of water evaporating. You always need to ensure water level between maximum and minimun level to avoid battery plates being exposed to the air. In contrast, maintenance free type is fully sealed box and all of the acid is contained in special separators and plate. Even with high temperature,the maintenance free motorcycle battery will still have enough eloctrolyte covering the plates.

Regardless of whether you have a maintenance free model or conventional battery, for motorcycle batteries to perform perfectly only little monthly maintenance is required. Keep the battery charged to 100%, recharging when the lights dim, the starter sounds weak, or the battery hasn't been used in more than two weeks. Other than that, you should follow this simple check list every month;

1. Keep the top of motorcycle batteries clean, dry and free of dirt.

2. Clean the terminals for the prevention of corrosion.

3. Check the electrolyte level. For conventional motorcycle batteries, make sure to keep the acid level between upper and lower lines indicated on the container.

4. Check inside motorcycle batteries for excessive sediment, sulfation or mossing. .

5. Make sure the exhaust tube is free of kinks and clogs and check cables, clamps, and case for obvious damage or loose connections.

6. Replace caps firmly

7. Do not let the battery stand in a discharged condition.

8. Charge battery once a month.

9. If you store your motorcycle for a long period of time (~ 30 days), plug in a good quality battery charger to maintain a proper charge.

10. Protect motorcycle batteries from strong impacts or shocks. Don't drop it!

Author: Zamlan Shamsuddin

About the author:
Zamlan is the owner of http://the-motorcycle-batteries.blogspot.com which provide usefull information and tips regarding motorcycle batteries.

Article source: Free Motorcycles Articles.

Our hands are just as important as any part of our body and most overworked part of our body. It is the one main reason why we should protect them. Even while riding a bike, like jackets, pants, chaps, boots, helmets etc gloves are an important gear, which you can never neglect to buy. That's why commonly used protection is a good quality pair of gloves.

Varied materials are used for manufacturing gloves these days. That is why it is important to know what type of material you want your motorcycle gloves in. Therefore, it depends on buyer either to buy leather gloves, or mesh or Cordura gloves. The type of glove you get will depend on what type of weather you will be normally riding in.

Best bet would be to go with a set of gloves that are good ventilation is required. Coming particularly towards mesh gloves merits i.e. Mesh gloves keep your hands comfortable and well ventilated yet safe. They also help you attain a good grip on the handles.

If you are worried about feeling suffocated, heated, then mesh gloves are best way out for all your worries. Gloves made of mesh ensure rider steering across with complete comfort which brings total control over bike.

Have you ever wished that gloves had more ventilation? At jackets4bikes Mesh gloves have just that ultimate desired feature in gloves. Some of the mesh gloves are made of premium quality 0.7 - 1.0 MM cow hide leather and mesh. Leather is use where good grip and durability is needed. Mesh is used where maximum ventilation around hands is needed. Result is an excellent quality pair of gloves that will match any black color jacket or racing suit. While some gloves of mesh are made of clarion synthetic suede and air mesh. These materials make this pair comfortable to wear with excellent ventilation.

Gloves at jackets4bikes also use ballistic poly mesh with leather. These materials make this pair comfortable to wear with excellent ventilation. Many other pairs of gloves have top quality Mesh & 0.8mm Top Grain Cow Hide Leather also containing comfortable lining to keep your hands comfortable.

Last but not the least many gloves from the lot are manufactured with 0.5mm leather and air mesh. These materials make this pair comfortable to wear with excellent ventilation and flexibility.

Mesh gloves are not only restricted for males but females have a wide variety available to them also, which makes it easier for ladies to buy those feminine colors as well as bold practical color of pair of gloves for themselves.

Now days you can easily buy well mesh gloves through online shopping. There are shopping web sites that are particularly dedicated to provide such clothing that are ideal for the biking.

It is very easy to shop at these online locations as you can sit at home and order your motorcycle gloves and other needed accessories. But gloves are a must motorcycle apparel and a biker should buy them. Motorcycle mesh gloves surely give needed protection!

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

Chicago is the city with lots of fantasy and fun loving things imbibed in it. The people at Chicago are ardent lovers of motorcycles. The people are very much aware of the brand names that thunder them down with comfort and technology that they provide to the customers. There are days with people left with lesser number of motorcycles. Now a day the roads at Chicago are flooded with motorcycles ranging from mopeds to super bikes. There are several types of motorcycles available in the modern era of science and technology. With the advertent changes in the field of automobiles, the manufacturers are drawing people to go in for motorcycles than cars. Motorcycles are not available to people directly. Several dealers, who in turn may or may not have sub-dealers, market them. These dealers have direct contact with the motorcycle manufacturing company and pursue the training form them to serve the customers at the time of adversity in systematic manner. These dealers have been recognized under the laws framed by jurisdiction of Chicago. Dealers at Chicago are bound to satisfy the needs of the people. The some of the dealers available at locality of Chicago are listed below:

 Motoworks:
At the S. Western avenue, near Harrison Park Motorworks have established themselves. People, who intend to buy the products of the manufacturer Vespa, can approach the showroom at any time. The engineers at showroom have been well equipped to deal with the requirements placed by the customers. The sales wing in this dealer organization has done a remarkable job by educating people with the ways to maintain their motorcycles in good condition. This dealer also enables service at the doorstep. Professionals from Motorworks come to the customers place and take the motorcycle for service. Also they place the motorcycle safely after service. All the customer needs to do is place a call to the dealer.

 Champion Cycle center:
Champion cycle center have their head office at the N. Western avenue at Chicago locality. They are specialized in marketing the products of Yamaha. They offer several attractive offers to the customers so as to make them happy. Also the people have responded ethically to the promotional offers placed by the firm. This dealer is expert in servicing the products of Yamaha with the sophisticated tools provided by the company so as to safeguard the parts of motorcycle. Hence they give a glossy look to the motorcycle as provided by the company during the delivery of the motorcycle form the manufacturer.

Author: Hendrik Kleinwaechter

About the author:
To make you equipped about the details of dealers at Chicago do visit Chicago motorcycle. This may help to trace out and plan your investment in an organized manner.

Article source: Free Motorcycles Articles.

Every year many motorcyclists that die from accidents are because they did not equip themselves with the vital protective gear that will help reduce the risk of injury and trauma.

Although now a day's youngsters carve for something fashionable it is still recommended that you use the appropriate ones such as helmets and jackets that are designed for motorcycle riding with main concern on protection while being manufactured.

A must and an essential gear you should own is the jacket. These jackets are available for both men and women in many different styles, designs and colors. Mesh motorcycle jackets have been gaining in popularity over the years. Leather jackets very often fail to provide relief during very hot summer rides.

Mesh jackets essentially make our rides pleasant and comfortable because these jackets allow for superb circulation of air making them more appropriate for wearing in scorching heat.

Some of the outstanding features of mesh motorcycle jackets are Made of Ultra Breathable abrasion resistant light weight poly mesh. These jackets have CE Marked/Approved five section removable dual density armor for back, shoulders and elbows. This Armor is completely removable through Velcro locked pockets.

Mesh jackets also have Velcro waist belt, elastic panels and zippers provide three levels of sizing control around waist. Icing on cake is Mesh liner for maximum air flow with two external pockets. Sleeve zippers and Velcro provide excellent grip. This jacket also has multiple 3M reflective tape in front, back and sides.

While some other types of mesh jackets have common characteristics like that these are made of Ultra Breathable abrasion resistant weight nylon mesh along with 1.2mm cow hide milled top grain leather use in area of stress (elbows, shoulders and back). While five section injection-molded removable armor for back, shoulders and elbows. This Armor is completely removable through Velcro locked pockets. There is also dual density layer of protectors build into the elbows, shoulders and back built into the jacket.

These types of Mesh jackets have full sleeve removable quilted liner. Protection issue is dealt with 360 degree reflective tape around chest, which makes rider more prominent while riding.

Mesh jackets have thicker fibers with an 'open weave' enabling free movement of air inside the jacket. Such jackets are a blessing in scorching hot weather.

Mesh jackets are made out of different materials with perforated leathers, mesh and other light materials. Although leather jackets are all time favorite of many traditional bikers, it can't also be denied that mesh and textiles are gaining popularity because of the need of ventilation during summers especially.

Many types of mesh jackets are available today. Hundreds of manufacturers make excellent-quality jackets for both men and women.
Nowadays manufactures are in raging competition for making mesh jackets which is also very beneficial for consumers because they have better options in choosing high quality motorcycle jackets.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

Car battery chargers are common items of vehicle maintenance equipment - they're cheap, portable and easy to use. But if you ride a motorcycle, a battery charger is often one of the most overlooked pieces of equipment in the average biker's workshop. There are several good reasons why (if you haven't already bought one) a motorcycle battery charger should be on your shopping list.

Motorcycle batteries are much smaller than car batteries and loose their charge relatively quickly. Wet cell batteries also require topping up with distilled water more often, and when carrying out regular maintenance on a motorcycle battery they may require a booster charge to bring them back up to the correct voltage. Motorcycle battery chargers quickly recharge the average motorcycle battery, getting you back on the road within minutes rather than having to wait overnight for the battery to charge.

Motorcycle batteries are exposed to the elements to a much higher degree than car batteries, and so are more susceptible to losing their charge due to cold weather. Motorcycle battery chargers are designed to deliver a rapid charge to a battery that has been affected by cold weather, enabling you to start the engine quickly and use the motorcycle's internal charging system to finish the job.

A motorcycle battery charger is compact, taking up very little room in your garage or workshop. If you carry out your own servicing, detaching the battery and doing a full check and recharge means that your battery is ready for action when the next sunny day comes along. This means that you can get out and enjoy a good ride without having the frustration of a bike that won't start because the battery is flat!

Letting the battery run flat repeatedly can actually damage the internal plates that are an integral part of the battery's structure. This can become expensive very quickly, as motorcycle batteries are costly items. A motorcycle battery charger will pay for itself very quickly by keeping your battery in tiptop condition. It also means that you are doing your bit for the environment as batteries cannot be recycled and go to landfill. By maintaining your battery, you're saving money and the environment.

Another good reason to use a motorcycle battery charger is to increase the potential lifespan of the battery itself. Motorcycle batteries take lots of abuse, from heat and vibration to weak charging systems and too many power-draining accessories. If you're a dedicated all-weather rider, accessories such as heated grips or even fog lights can quickly drain a small battery. Once the bike has been parked up attaching a trickle charger will boost the battery, ensuring that it's ready to go when you next start the bike up.

If you're serious about motorcycle riding or just a fair weather rider who only takes the bike out on sunny days, motorcycle battery chargers are a must-have item in your workshop. You check the oil, you check the petrol so why not check the battery? Without it, your bike isn't going anywhere and you're missing out on all those fun rides for the sake of a flat battery. Motorcycle battery chargers are cheap, portable and efficient and if you haven't invested in one already, they should definitely be put on the top of your shopping list.

Author: Alan Cooke

About the author:
Alan Cooke sent the useful information on Motorcycle Battery Chargers. A detailed description on Motorcycle Battery Chargers is found here for those interested.

Article source: Free Motorcycles Articles.

Motorcycle lovers really understand the importance of a luggage carrier to be secure and comfortable while being out on the drive. Being out on bike is totally 180 degrees opposite experience than from travelling by other means. And this is because of its nature, open ride by category and very limited space to carry any luggage. This being the reason enhances the importance of carrying any travel/tool bag sort of thing with you while on drive.

So those who always thought of carrying any tool box as foolishness shall understand why it is much desired and growing in popularity day by day. Another reason of carrying a bag along with you is that as even described above, now there are luggage that are specially made only for motorcycle trips. Of course who would not want personal possession's safety and comfort while enjoying the ride along side.

Biking on road is highly prone to accidents which are unseen and may be unfortunate as well and the needed safety measure of motorcyclists can save them from impending danger and risks. Tool bags are therefore very vital, investment of few dollars is worth it actually. Having a tool bag while you are out on ride and you can solely depend on these bags May it rains, hails or u ride on a troublesome bumpy roads. These accessories can also give you thrilling, hassle-free rides by giving protection needed to your possessions or if you want to carry tools with you while on out on your ride. High-quality street motorcycle tool bags will surely give you the finest and most durable motorcycle accessories that you badly needed in your everyday routine.

They are offered at competitive prices yet being high quality products, good for personal use and can be impressive if given as a gift to someone as well. Some of the distinct features of these tool bags available here are that these bags are 12 inch length (on outside) and 4.5 inch diameter having extra heavy duty straps and roller buckles. These tool bags are standard sized to fit almost all motorcycles brands. Highly weather resistant design and materials used. Tool bags are rigidly constructed to maintain shape, even when empty. Reinforced stitching and durable construction allow many years of use of tool bags. These tool bags are treated for water resistance to keep your bags looking good for years. High quality straps and buckles to secure on front forks and withstand the strongest of headwinds. Anyone who can work with tools can easily make modifications to fit this tool bag anywhere.

These tool bags are small leather or nylon bags made to hold tools, either in a roll-up configuration, or simply as a pouch. Often stored under the seat, it helps to keep your tool kit organized, and safely stored

When choosing motorcycle tool bag, some criteria needs to be considered for choosing best one of your choice. Firstly decide about the size and capacity that you need to have. This is very important factor indeed, because it relates to your budget even. Choosing a large size tool bag which your budget can allow, surely allows you to have a bag according to the amount of money you can invest in a tool bag. Generally, motorcycle tool bags require very low care and maintenance but you still have to look after them from time to time.

So whatever tool bag you choose always go for your preferences and too bags are available in varied colors so matching the color scheming with bikes is not an issue these days. Just choose the right tool bag from right manufacturer/seller. After all value for money is what buyers actually look for! And top quality speaks itself.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

Most drivers neglect to rotate their vehicle's tires. They know instinctively that treads wear down over time. They also realize that worn treads reduce fuel efficiency and can eventually present a safety risk. The heavier the brake rotors the more heat they absorb fading less giving a better braking performance, are more stable and rarely warp as this is a cause of pulsating brakes.

Whenever you drive your car, the friction generates heat, which causes the treads to wear down. When you rotate your tires, it relieves the pressure created by friction on those placed on the front axle. Remember, those in the front wear down more quickly than those in the rear. For example, they'll swap the driver's rear and passenger front, and passenger's rear and driver's front.

Unfortunately, it is the accountants that win and brake rotors are built to weigh less. It is possible to make brake rotors that are light, stable and powerful. The Porsche 911 Turbo model offers a higher performance brake option, and stops in an amazingly short distance with its stock brake system.

Many are stuck using standard cast brake rotors. When the rotor becomes warped, it wears from side to side unevenly, causing it to rub against the brake pads. If rotor sides aren't parallel, this will cause the pistons in the brake calipers to make the brake pads push in and out at a rapid pace.

If tightened incorrectly, this can also warp the rotor. Any brake pulsations after the wheel has been changed may mean having to loosen the wheel nuts and re-torque. Brake rotor run-out can also be a cause of pulsing brakes. There are cars that are sensitive to rotor run-out if more than 001 inch, which will cause brake pulsations will occur.

It is better to take certain steps in trying to prevent or correct brake pulsations, mounting surfaces should be kept clean, if machining rotors make sure sides are parallel, rotor run-out should be kept to a minimum, to torque wheel nuts always maintain to use the proper procedure, hopefully brake pulsations will be in the past for your vehicle.

Author: axious

About the author:
I am student at University in Indonesia and to learn more about wrench and safety tips used hand tools visit at http://www.speciallywrenchsetstools.com/torque-wrench



Article source: Free Motorcycles Articles.

Never ever try cutting costs when you are buying protective riding clothing, you always get the quality for what you actually paid. Thinking to buy some good motorcycle leathers but don't know what to buy. Then shouldn't you be searching to buy the best stuff and available with maximum protection?

If the leathers are your choice then you should know it should be the fitted one with maximum flexibility in movement and shunt be baggy like in shape. Buying custom made leathers for riding is a very costly option, so why not just spend some dollars on something readymade available around you, yet convenient to buy. Leathers are to be chosen when they do best fitting.

Now a days leather is not only an outfit to give warmth in cold season, it's been known for completing lifestyles, safety issues if with best protection. A common necessity and wearing for bikers carving to be a fashion symbol yet all protected from head to toe.

Leather for biking can be worn anywhere and is used at all times. Durability, flexibility, lasting nature, protective, versatile are worth mentioning distinct features of motorcycle leathers; and are absolutely doubtless about them.

In leather there are almost all types of accessories available ranging from jackets, gloves, biking suits, bags etc. For example Leather Jackets are available in many materials including i.e. cow hide leather, analine leather etc. Leather jackets are available in different forms and styles like motorcycle jackets, racing jackets for men and women. Water proof leather jackets and perforated leather jackets are also popular among people.

Motorcycle leathers are friendly in all seasons and yet too comfortable; they look good at all times of the year. In summers leather clothing keep you cool while in winters they protect you from cold. They are a true fashion icon; yet practical. This uniqueness is what that only that departs leather clothing for biking from all other material dresses.

Get leather instead of any other textile like Cordura or mesh as it is the best material to use. I have used both and would prefer for leather now after coming off with different textiles on.

Very reliable reasons are that leather clothing/accessories must be used, and most of them are too linked with abrasion resistance and weather friendliness. Generally other textiles are lighter, and can be also being bought with waterproof features. But if you don't ride in a lot wet conditions leather is a better option, and doesn't have to be too cold or too hot.

Now a days waterproof leather clothing used for making motorcycle apparel for bikers is also available which makes it a lot better for rider to buy their desired clothing with all features in one item. Leather can be treated and is available readymade with shower-resistant feature, but if you get caught in a downpour while normal leathers on, a wet leather suit is certainly not a nice thing to be inside.

Coming to cleaning and maintenance issues, there is no need to wash leather clothing after coming back from a long ride, every now and then. Simply wipe it with a wet cloth and here you go. Polishing it once in couple of months is advisable. There are never any hassles unlike motorcycle clothing made from other materials which require regular dry cleaning and some also take long hours in a day to dry.

Protective motorcycle leathers must last for years and years if you look after them properly, yes it might seem bit expensive but one time investment for a fruitful time ahead is actually not a big deal, as you won't need to replace them for a very long time.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

When it comes to selecting the perfect jacket for you from all of the various types of Leather Motorcycle Jackets, it is important that several things are kept in mind. The first is the quality of the material. If it is going to fall apart then you have defeated the entire purpose of the leather jacket. This will mean that you may have to pay a little more for your jacket.

Safety, comfort, and storage is certainly worth it though so do not turn and look away just because of the price. Since this is your safety and comfort you are looking at, it is important not to go the cheap route, as that will get you nowhere. Of course most people already know about needing comfort and safety from their jacket, but storage?

The answer is yes because storage in a jacket, such as many zippered pockets is extremely important. Since you are on a motorcycle you need all of the additional storage space you can get. Taking all of this into consideration, the most popular of the Leather Motorcycle Jackets is that of the full jacket.

The full jacket is one that everyone on a motorcycle should have in his or her collection. The leather protects your entire upper body, arms, chest, and back. Whether it is to be protected from the harsh weather elements you come across or to protect your skin from the pavement, the full jacket is something that you cannot pass up on.

Then there is the vest, which some consider the half jacket. While there is a lot of comfort with this, it is no comparison to the full Leather Motorcycle Jackets. The full jackets can be comfortable too if you get the correct size. You will want to remember that the vests will not be able to protect your arms against nature of road burns should you have an accident.

So even though purchasing your leather gear for motorcycling riding should not just be about getting what is the most popular in order to fit in, you will want to consider why such items are more popular then others. It is probably because they are the best made and the most efficient for your motorcycle riding.

Since you are looking for a leather item that is going to protect you from the elements, from an accident, and keep you comfortable, make sure that you are putting a lot of time into the decision making process. Before you make your purchase you will want to make sure that you are measuring yourself in order to get the right size. Ask the shop owner questions if you have any since that is what they are there for.

Take your time and take the suggestions of the shop owner, as they know what they are talking about when it comes to leather clothing for motorcycle riding. Go with the best, the most popular, and trust the word of the professionals and you will be on the right track.

Author: Brian Garvin & Jeff West

About the author:
Let Brian Garvin and Jeff West Teach you more about Motorcycle Leathers and Leather Motorcycles Jackets at the Motorcycle Leathers Shop.

Article source: Free Motorcycles Articles.

You are our and enjoying the lovely ride with your one of favorites motorcycle apparel on and suddenly it starts raining on you, ruining your trip, your apparel and your mood. That really often makes you annoyed and agitated to highest levels. It definitely means; now the time has come to think about buying a motorcycle rain gear.

The advances of modern textiles could save you from the trouble rain can actually give you. Top quality motorcycle rain suits have high waterproof technology materials used for their manufacturing. Numerous styles and colors to for a rider to select from, the options never end and you can easily find matches to your taste. Some rain gears also use durable heat resistant inner leg lining to protect the rain suit from becoming melted due to high engine and exhaust temperatures. When finding rain gears, a motorcycle rain suit that has reflective material is also an additional best feature as well as important. This raises the chances to highest levels of others seeing you in bad weather.

Some merits of buying motorcycle rain gear are that these keep the mud off your motorcycle Jacket and pant. Secondly it also helps you to stay dry and warm in cold and moist seasons. Rain gear acts as another barrier to the Wind which is a great deal. It surely allows you to ride in foul windy, stormy and rainy weather. You can surely hose it down, saving precious time on cleaning. And last but not the least wrinkles never matter, just roll it up and stow it away.
Rain gears are available in one piece and also in two pieces as well. This totally depends on the choice of biker which so ever of two types he/she likes to buy. Raingears at jackets4bikes are usually made from nylon and are absolutely 100% waterproof. Quality Waterproof Nylon that is 100% water and wind proof. Outer shell is very flexible which is ideal for wearing it by itself or over normal wear or riding wear. The exterior is waterproof and the interior is lined to keep you warm. Some liners are removable making the jacket even more flexible. Fixed poly lining in jacket, this keeps the inside of rain gear warm yet comfortable as well. Some other distinct features of rain gears are rain flap over front zipper with 2 large outer pockets. Adjustable Velcro and elasticized cuffs for snug and comfortable fit. Elastic waistband in rain gears is for better fit and additional comfort. Sealed seams are to prevent leaks. Rain gear is very convenient and easy to wear. You should have plenty of reflective markings on the jacket and pants because rain means dreary and dull skies and you will be harder to spot. This issue is no more with rain gears available at jackets4bikes. The 3M reflective safety tapes on both jacket and pants of rain gears.

If you really want to buy motorcycle rain gear, it just tells how much you are actually fond of biking may come what in your way. An extremely wise investment which eventually pays you off and this realization comes on you when it actually rains like cats and dogs, and you are all geared up with perfect motorcycle rain gear many miles far away from home on your ride. As for some people, winter is a time of the year to roll their chopper motorcycles into the garage, put the battery on a slight charge and then wait for spring to feel the ecstasy of wild ride. On the contrary buy a perfect motorcycle rain gear and feel the craziness of ride in rain.
But for people like yourself; enthusiastic riders, you won't let a little rain deprive you of a good ride.

The motorcycle rain gear options are just so wide that it needs whole brain and information to decide the best manufacturer and seller for you. Jackets4bikes is one top quality manufacturer and seller that will have you going in the right direction. Whether you choose basic or luxurious rain gears what's most important is that you have it to wear when the rains come.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

A helmet commonly refers to a kind of protective headgear usually used by motorcycle riders. The main aim of a helmet is to provide safety and safeguard the riders head in an accident. Nowadays advance helmets offer additional conveniences like, ventilation, face shields, ear protection and intercom.

One of my friend met with a fatal accident while he was driving on a narrow lane. Suddenly a dip in the road blocked his view of two small boy crossing the lane. While saving them he lost the control of his bike and hit an oncoming car. At the time of accident he was not wearing a helmet and suffered serious head injuries. He was in coma for a week and finally died. His life could have been saved if he had a helmet on his head.

A study conducted by National Highway Traffic Administration reveals that bike rider is 35% more likely to get hurt or even die while driving in comparison to the automobile driver. The helmet reduces the chances of a head injury and the resultant death to a considerable extent.

Helmets are widely acclaimed for considerably minimizing injuries and fatalities in case an accident occurs. Several countries have enacted laws that makes it mandatory for the motorcycle riders to wear a helmet.

There are several types of helmet available in the market and includes, full face, off-road/Motocross, modular/flip-up, open face and half helmet. Always wear a light colored helmet as it enhances the visibility to a considerable extent. According to a research white color helmets reduces the chance of an accident by 24%. The research further added that riders wearing reflective or fluorescent clothing reduces the chance of any mishap by 34%. Finally, everything depends upon you as you have to decide to what extent you want to be visible to other road users, while riding a bike.

Nowadays plastic is used in the construction of the helmets. Expensive and high quality helmets are strengthened with kevlar or carbon flier. Advance helmet possess both fabric and foam interiors for advanced comfort and security. Every helmet has a hard outer shell to avoid penetration of the helmet by a sharp object, which may puncture the skull. Utmost care is taken to provide structure to the inner liner to prevent disintegration when a person fells down on losing his control. This is important because the foams used have very little resistance to penetration and abrasion. A foam liner is also provided to crush during any collision which enhances the distance and time duration over which the head stops and minimize its speed.

Don't always go for the cheap one. For high quality, convenience and protection you need to shell out some additional bucks. After all, helmet design is all about the tolerable impact the head can handle.By buying a unique motorcycle helmet you can provide an attractive addition to your get up. Everyone will start noticing you and soon you will be popular among avid motorcycle riders.

Author: Troy

About the author:
My name is Troy, I am wholesaler dealing in Motorcycle Helmet.


Article source: Free Motorcycles Articles.

Motorcycle apparel gives safety. Protection is such a vital aspect which a rider should never even dare to over look. Every day, each year many bikers die in unfortunate accidents while out for riding. Numerous lose their limbs thus ruining their lives forever, depriving themselves from every happiness they would have better enjoyed if this wouldn't have happened.

According to research carried out on these accidents it has been proved that chances of injuries can be minimized by wearing protective gears such as motorcycle protective jackets, pants, boots, helmets etc.

Therefore, it is sounds reasonable and even vital for all bikers to spend some dollars and save their lives rather than threatening their safety while riding around. Protection is better than cure as we all know and protector jackets will enhance your safety minimizing effects on an unfortunate collision or accident.

Nowadays, numerous companies are manufacturing and selling protector jackets, available in various colors, designs and styles. Protector jackets are available for both genders, as the competition to provide the best quality protector jackets is increasing day by day.

Protector jackets are available in different materials such as leather, mesh, textile but the most common materials amongst all is always leather. Leather protector jackets are the most popular and traditional choice, but one cannot ignore the fact that textile and mesh protector jackets are also gaining popularity day by day.

The protector jackets, especially helps by:
� Softening and cushioning impact
� Preventing abrasions

What does one mean by maximum protection for your upper body i.e. shoulders, back, elbows, chest, and arms? Now, the manufacturers of protector motorcycle jackets incorporate impact protectors' i.e. hard protectors and dual density foam in the motorcycle jackets to enhance the protection the jackets; being offered to motorcyclists.

The impact protectors must be incorporated for all these areas. So when you are purchasing a motorcycle jacket, you should feel the elbows and the shoulders and should find impact protectors incorporated into the jacket.

When looking to purchase a protector jacket, make sure the armor is CE marked and approved. This 'CE' Certifique Europe is a European standard of certification that grades armor on three levels, level 1 being the least protective, level 3 being highest in protection.

Ultimate combination of impact and hard CE marked/approved protectors and abrasion resistance at the right places makes biker's motorcycle protector jacket very reliable in protecting biker from injuries, giving truly needed value for money.

Here is an important pointer for all those persons who do not know the difference between a protector jacket and an ordinary jacket for rider. If the shoulders, elbows and back are not reinforced or are merely padded up with extra cloth, then what you are looking at is an ordinary jacket, and is not a protective gear al all to wear.

The mere presence of impact protectors in the elbows and the shoulders region is not sufficient. Needless to say, the high abrasion resistant material should also give forearms, back and chest area desirable safety.

Give some serious look at protector jackets the next time you go shopping. Shopping around over the Internet will surely find you a number of categorizes for motorcycle protector jackets.

Depending on your choice surely you will find what so ever type of protector jackets you are craving for. Be sure to buy from a trusted website that is secure and reputable offering top quality products at competitive prices, with huge variety. Buy best and enjoy ride on open road.

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

Crashing a bike is that horrible that all riders really want to avoid. Bikers generally think that if you have to position yourself just before an unseen and undesirable bike crash then either you have to try at most to avoid this disastrous situation or at least minimize its effects by wearing something protective.

Serious injuries also result when motorcyclists stop sliding and roll like a rag doll with their arms and legs sticking out or when they hit something solid, like trees, curbs and other road users. A high slide is another thing that can give biker hard and serious injuries. Mostly bike's crash happens in a split second that there is actually no time to react or do something about it. Hitting a tree or sliding in dirt is a lot more different than hitting another vehicle on road.

Ride safe, ride defensively and presume that every car around you is driven by someone not paying attention. Or whatever causes accident and injuries this surely is going to cause a lot of trouble to riders and that is the reason why motorcycle safety apparel is a must. Including apparel lists does include spine protectors for sure!

If you really want a safe ride or to minimize the harshest effects of any accidental collision, ask be sure to get protection i.e. spine protectors. Equipments and proper accessories are that matters the most after training for motorcycling.

Because of these factors of unpredictability regarding safe ride; it really is vital to wear your spine protector every time you ride, These spine protectors can also be used on street bikes, motocross, drag racing, and any other motor sports.

Spine protector can save riders from most whiplash injuries. These injuries are caused by the sudden and unexpected movement of the neck or head during a road accident. It affects the soft tissues of the neck and the cervical spine. Commonly whiplash injuries are associated with the bike accidents, caused by a sudden jerk to neck or head. The main reason for this is, because of the soft tissue in the neck and the cervical spine that is affected so easily. A cervical vertebra is connected directly to other soft tissues like ligaments and muscles. When the sudden or unexpected movement is occurred, the muscle and ligaments are affected and it follows the cervical vertebra as they are all connected together.

All of your worries will be taken care of, only if you grab a spine protector for yourself before over indulging our self in adventurous and dangerous riding and biking sports. Because these injuries give neck or back pain; neck stiffness, soreness, and finally it will quickly interfere in all your daily activities. Consequences of injuries to neck may vary from mild pain to severe damage and sometimes even lifelong disability which leads to restricted head movement, damage in cervical spine or forever lasting severe pain.

Protection is better than cure so why not be playing safe and enjoy the adventures yet to come in your life!! Best spine protectors with marked/approved CE protection are available at jackets4bikes

Author: Sue Adams

About the author:
Sue Adams is content contributor for Jackets4Bikes. You can find more top line products for motorcycle riding on Jackets4Bikes. Use this article freely but please leave the Author Biography and Links intact.

Article source: Free Motorcycles Articles.

It's time to feel the spirit of bliss with mini dirt bikes. Looks like, the thirst for these sleek mean machines is never ending. Icon for the youth, they are the safest on fast tracks. A truly magnificent mean machine and pioneer fantasy bikes for young adults. Those who love driving their mini bikes are ever ready for any outdoor adventure. To look at these roaring vehicles are actually off-road motorbikes, lightweight and are usually driven on cross country dirt roads unpaved, uneven or rough grounds. Apart from being the most prevailing off-roader, the mini dirt bikes can also be tagged as the most seducing bikes luring youngsters with a passion for the wild. These dirt bikes were conceived for riding on irregular landscape. They are solid and are fitted with suspension and rugged tires to enable the rider to move at a fast pace. These gorgeous bikes also come with smaller engine power unlike the actual street bikes that one sees on roads. Mostly they have 125 cc engines. Mini dirt bikes are light but muscular with twisted tires to offer maximum grip on uneven terrains.

Globally youngsters love owning mini dirt bikes as they symbolise excitement and adventure for the rider. These bikes can be started easily and can confer mud-covered paddocks and hill slopes during all weathers. Mini dirt bikes provide outstanding mileage even at high speeds and are super cool and fabulous to ride. These kinds of bikes can be gas powered or even electrically powered but they still provide good mileage which is one of its best features. These hot bikes are available in 49 cc, 50 cc, 70 cc, 100 cc, 110cc and 125cc. Excitingly, many models come fitted with attractive features like speed governor, that permits the adult to set a top speed at which the bike will go. Even the exhaust pipes are so well placed that it doesn't disturb the rider in the course of riding.

Bike enthusiasts will find an overwhelming variety of classy mini dirt bike models in the market. Before buying ones needs to carefully choose the right one that suits the requirement, budget and the engine type. These bikes are typically designed for traveling on uneven landscapes. They are manufactured by reputed bike makers like Honda, Pantera, Yamaha and Razor. Many banks lend loans to serious buyers. Sporty mini dirt bikes add glamour to the youngster's lifestyle!

Author: Alice Shown

About the author:
If you are looking for more information on Mini Dirt Bikes, visit TheSportsBikeshop.com.

Article source: Free Motorcycles Articles.

Regular maintenance of your motorcycle is necessary to ensure that it is in top shape every time you use it. That is why you have to check it after you take it for a ride. You have to schedule a regular monitoring after using your bike. It can be tiring to check it right after your trip. That is why it is better to rest first since you will not be able to check your motorcycle properly if you are thinking of your bed.

Using the T-CLOCS is the best way to check your motorcycle. This is an acronym provided by the Motorcycle Safety Foundation to help the riders check all the parts of their bike before they leave. It stands for tires, controls, lights, oils, chassis, and stands. You can use this checklist to check the motorcycle after you take it for a spin. This is necessary if you are going to use the motorcycle daily.

Here are some maintenance tips you should do after using your motorcycle:

1. After using your gears, you will take it off and clean it, right? You need to check the men's leather gloves for dirt and possible damage, the same with the other gears. If you do this to your gears, you need to do this to your bike as well. You have to clean it and check it for damages.

2. Follow the T-CLOCS checklist. It is important to check these parts especially if you have been from a rough trip. Check the chassis. Some portion of the frame can have damages from the rough road. Check the wires and cables as well. The trip can cause some of the parts and controls to loosen. Check the oil level as well.

3. If you are going to store your motorcycle for a long time, it is better to do a thorough check up on your motorcycle. If you are going to store it for the winter season, do the following:

a. Follow the T-CLOCS when storing your bike for the winter season. Check everything. Do the same when you prepare to ride it after the cold season is over.

b. Drain the oil from the motorcycle tank. This will prevent the liquid from changing to substances that can damage the internal metal of your oil tank. You can replace it with new oil.

c. Remove the battery from the motorcycle and store it in a warmer room. If you do not want to take your battery out, you can attach a battery tender. The battery tender will ensure that you will not overcharge your battery.

d. Covering your motorcycle is very important. Invest in high quality motorcycle cover. The cover will protect your motorcycle from external factors. In addition, it will keep your motorcycle warm.

Keep in mind that your motorcycle is your responsibility. All the gears that you use for riding are included. Aside from cleaning the men's leather chaps, jackets, boots, gloves, and helmet, you have to check your bike regularly as well. As what most riders say, if you take care of your bike, it will take care of you.

Author: Jenny Carson

About the author:
For more tips and information about men's leather chaps, please check out http://www.outbackleather.com/motorcycle-chaps.


Article source: Free Motorcycles Articles.

Whenever a person decides to buy a new motorbike or perhaps just improve the condition of their own, there are a great many things that can be purchased as upgrades. It can sometimes be hard to decide what to buy first. There is a natural reaction to buy the items and accessories that will look great, but this can sometimes mean overlooking some of the most important items that a bike, scooter or any sort of vehicle really needs. No matter how funky or classy the bike looks, if it is unable to stop efficiently when needed then it won't be a worth a thing. There is no doubt that safety has to be a massive consideration for all bikers and this puts a great emphasis on them to buy brakes.

Depending on what type of vehicle they have, how they drive and where they drive, there will be different sorts of brakes that are better suited to them so it is up to the consumer to do a level of research before purchasing and find out what type of brakes are best for them. Driving on rough terrain is ultimately very different from driving on wet surfaces and the needs and requirements being placed on brakes will be different for both surfaces. Most people will have a multi-purpose or general style of brakes which will be sufficient for the vast majority of driving but there are always people who would benefit from a more specific type and these people have to be aware of what would best suit their driving styles and preferences.

Therefore, a lot of thinking has to go into the decision to buy brakes and although the financial issue can't be the only factor in the process, it is inevitable that cost will come into the final choice. Thankfully, there are many great brake pads and products to suit all budgets and there is no need to think that saving money on brakes is creating a bigger risk than is necessary. Just like all industries and all other consumer goods, there is a wide variety of products to be found which will ensure there is something for everyone. A small financial saving may seem great at the time but you can't really put a price on personal safety; whilst it is wise to shop around in an attempt to get the best quality deal on brakes that money can buy, always make sure that the brakes are reliable.

When the decision is made to buy brakes, it is vital that the biker is fully aware of what types of brakes are compatible with the bike before they spend any money. This is important as it can save them money and inconvenience if the wrong brakes are purchased. More importantly the consequences involved with a bad decision when they buy brakes could prove to be massively negative and extremely dangerous. Fashion and flair are undeniably important features to consider in brakes, but functionality must never be overlooked.

Author: Andy Freeman

About the author:
Premium quality EBC brake pads and rotors for cars, trucks, motorcycles, is our business .... all made in the UK.For further information regarding where to buy brakes for a wide range of vehicles including automobiles and motorcycles, please visit our website at http://www.ebcbrakes.com.

Article source: Free Motorcycles Articles.

How did you learn to ride? Well I was just checking out some information on how to learn to ride a motorcycle and I started thinking how did I learn to ride. I remembered my first ride it was on a little dirt bike that my buddy had and a bunch of us were hanging out in the woods and then he rode up with his bike everyone there had ridden before except me but they didnt know that. So he was letting everyone take turns and than it came to me and when I steped up for my turn my buddy asked if I knew what I was doing and I dont know why but I just said yes. I could have said no and I am sure he would of showed me but instead I said yes hopped on, did what I thought was correct and in about 30 seconds I was in bushes being laughed at. That was my first and last ride on his dirt bike. After that I really cant figure out how I learned, most of it was just trial and error which now as I am older I really dont think that was the best way to learn but I surrvived. As an adult I was required to take a basic riders saftey course and when I first found out I had to go I was totally against it, I had been riding for years what were they going to teach me. But I have to say I learned alot of stuff I never even thought about and the class was enjoyable, it is also a great idea if you get a new bike you can always take another class it gives you a chance to learn your new bike in a safer enviorment. Well some how I made it and have been riding for many years now If your thinking about riding dont start out like me and make sure you get a bike appropiate to your experiance level.

Author: Brian

About the author:
Learn how to ride, ow to pass rode test,how to buy a motorcycle and more.http://ljpbsp.server3.hop.clickbank.net/


Article source: Free Motorcycles Articles.

Available Online If you are looking for a specific motorcycle that you cannot find in your local motorcycle shop, the best thing for you to do is to check online. The internet is not only being used as a means of communication and sending data, but as a venue for business and sales. This includes motorcycle auctions and sales.

Motorcycle fans and collectors look for old and new motorcycle models online. This is why motorcycle auctions are prevalent online. Vintage motorcycles are not the only ones available in motorcycle auctions. There are also used motorcycles of every make and model being sold as well as brand new motorcycles.

If you are the type of person who wants a unique and personalized motorcycle like no other, you can hire a company whose specific business is to create or design custom motorcycles. This works best if you have some knowledge about motorcycles to be able to implement your ideas into the design. However, if you do not have enough background in motorcycles do not be discouraged from wanting to have a custom design. Through good communication you can still coordinate with the vehicle engineers to have all of your ideas and features added. Right down to the last drop of paint, nut, bolt and screw.

Best Cycle Auctions is one of the online motorcycle merchants where you can check for the motorcycle that you have desired for years. It is one of the most popular and trusted motorcycle sales sites for any brand, make and model.

With the business of selling new and used motorcycles and making custom motorcycles, it is inevitable that motorcycle parts are also made available. The World Wide Web has provided a great deal of information that is readily available to everyone. You can check for ways to properly maintain your motorcycle. You can even create a motorcycle feature for yourself that is so unique that no one else will ever have that feature.

Online you can learn how to enhance the performance or trick out your motorcycle. Parts you can hardly find in your local bike stores you will definitely find online. If you are the type of person who is interested in the trends of motorcycle sales in the world market or just your local county for that matter, there are several websites featuring this information for professional motorcycle traders.

One of the best things about motorcycles for sale online is that you can find the model, the manufacturer and the year you are looking for in the comfort of your own home without ever having to waste any of your valuable time. People from all over the globe are using the internet to find what they are looking for and you should too. If you check Best Cycle Auctions today, you just might be lucky enough to find someone selling that one of a kind vintage motorcycle you have been looking for or just a fantastic price on the motorcycle you have wanted to buy. Don't pass up the opportunity. As they say, opportunity only knocks once. If you let it pass you by, you may never find that one again.

Author: Robert Bofman

About the author:
Robert Bofman is author of this article on motorcycle auctions.
Find more information about used motorcycles here.


Article source: Free Motorcycles Articles.